Home / Blog / Parallel Circuits
Parallel Circuits
Parallel Circuit Resistance: Worked Examples, Two Methods
Parallel resistance is a staple of electrician exam math. The idea is simple: add more paths and the total resistance goes down. The arithmetic is where people slip, especially the reciprocals. This guide shows both common methods, product over sum and the reciprocal sum, with five worked examples and a way to check every answer.
What parallel means
Resistors are in parallel when each one connects across the same two points, so each branch gets the same voltage. The OpenStax University Physics text states that the potential drop across each resistor in parallel is the same, and that the equivalent resistance is always less than the smallest individual resistance. Household branch circuits work this way: every receptacle and lamp on a 120 V circuit sees the source voltage, and each load draws its own current.
Resistance is measured in ohms. NIST defines it through 1 ohm = 1 volt per ampere, which is Ohm's law written as a unit.
Two formulas, one idea
Reciprocal sum (any number of resistors):
1 / Rtotal = 1 / R1 + 1 / R2 + 1 / R3 + ...
Then flip the answer: Rtotal = 1 / (the sum).
Product over sum (exactly two resistors):
Rtotal = (R1 x R2) / (R1 + R2)
Both give the same result for two resistors. Product over sum is faster on paper. The reciprocal method is the one that works for three or more.
Worked example 1: two resistors, product over sum
R1 = 12 ohms and R2 = 4 ohms in parallel.
- Product: 12 x 4 = 48
- Sum: 12 + 4 = 16
- Rtotal = 48 / 16 = 3 ohms
Sanity check: 3 ohms is less than the smaller resistor, 4 ohms. Good.
Worked example 2: three resistors, reciprocal sum
R1 = 10 ohms, R2 = 20 ohms, R3 = 20 ohms.
- 1/10 = 0.10
- 1/20 = 0.05 and 1/20 = 0.05
- Sum = 0.10 + 0.05 + 0.05 = 0.20
- Rtotal = 1 / 0.20 = 5 ohms
Again, 5 ohms is below the smallest resistor, 10 ohms.
Worked example 3: equal resistors
When every branch has the same resistance, divide by the number of branches. Three 60-ohm resistors in parallel give 60 / 3 = 20 ohms. Four 8-ohm resistors give 8 / 4 = 2 ohms. This shortcut only works when all the values match.
Worked example 4: four unequal resistors
R1 = 8, R2 = 8, R3 = 16, R4 = 16 ohms.
- 1/8 + 1/8 = 0.125 + 0.125 = 0.250
- 1/16 + 1/16 = 0.0625 + 0.0625 = 0.125
- Sum = 0.375
- Rtotal = 1 / 0.375 = 2.67 ohms (rounded)
You can also do it in pairs. The two 8s give 4 ohms. The two 16s give 8 ohms. Then 4 and 8 in product over sum give 32 / 12 = 2.67 ohms. Same answer, which is a good way to confirm your work.
Worked example 5: from resistance to current and power
The OpenStax example uses 1.00, 2.00 and 2.00 ohms on a 3.00 V source. The equivalent is 0.50 ohm, the total current is 6.00 A, and the branch currents of 3.00, 1.50 and 1.50 A add up to the total. The same pattern holds at 120 V. Put the 10, 20 and 20 ohm resistors from example 2 across 120 V:
- Branch currents: 120 / 10 = 12 A, 120 / 20 = 6 A, 120 / 20 = 6 A
- Total current: 12 + 6 + 6 = 24 A
- Check with Rtotal: 120 / 5 = 24 A. They match.
- Total power: 120 x 24 = 2,880 W
The branch currents add. The branch voltages do not: each branch has the full 120 V. See the Ohm's law and power formulas guide if you need a refresher on those relationships.
A two-lamp example
Two identical lamps, each 240 ohms, are on a 120 V circuit. Their parallel resistance is 240 / 2 = 120 ohms, so the total current is 120 / 120 = 1 A, with 0.5 A in each lamp. Remove one lamp and the other still sees 120 V and still draws 0.5 A. Total current drops to 0.5 A. That is why adding loads to a parallel circuit increases total current.
Common mistakes
- Adding the resistances. That is series. For parallel, the total must be smaller than the smallest branch.
- Forgetting the last flip. After summing reciprocals you have 1 / Rtotal. Take the reciprocal once more.
- Using product over sum with three resistors. The formula is for two. For three, combine two first, then combine the result with the third.
- Rounding too early. Keep full precision until the last step.
- Mixing units. Convert kilohms to ohms before you start.
Self-check
1. 30 ohms and 60 ohms in parallel? 1800 / 90 = 20 ohms.
2. Five 100-ohm resistors in parallel? 100 / 5 = 20 ohms.
3. A parallel combination comes out at 15 ohms but the smallest branch is 12 ohms. What went wrong? The total must be below 12 ohms, so check the arithmetic or whether you added instead of using reciprocals.
Keep practicing
For more circuit math, see wire resistance and the common exam calculation mistakes, or try the CircuitDrill course.
This article covers circuit physics, not code compliance. Code requirements depend on the NEC edition your jurisdiction has adopted, and your authority having jurisdiction makes the final call. CircuitDrill is an independent study tool, not affiliated with NFPA, the National Electrical Code, or any state licensing board.
Frequently asked questions
How do you calculate resistance in parallel?
Add the reciprocals of each resistance, then take the reciprocal of the sum. For two resistors you can use product over sum: R1 times R2, divided by R1 plus R2.
Why is parallel resistance smaller than the smallest resistor?
Each added branch gives current another path, so the total opposition drops. The equivalent resistance is always below the smallest single branch.
When can I just divide by the number of resistors?
Only when every resistor has the same value. Three 60 ohm resistors give 60 divided by 3, which is 20 ohms.
Does voltage divide in a parallel circuit?
No. Each branch sees the full source voltage. The branch currents add up to the total current.
Free
Get 5 worked problems right away
Voltage drop, conduit fill, box fill, Ohm's law and derating. One problem each, solved line by line. They open right after you sign up.
Voltage drop calculator with every step shown
Single-phase or three-phase, copper or aluminum, 14 AWG to 500 kcmil.